Perguntas Retrabalho em Virabrequim

Re: Retrabalho em Virabrequim

16/08/2008 às 01:26
#10873532
(y)

Por favor Entrar ou Registrar para participar da conversa.

Re: Retrabalho em Virabrequim

27/06/2009 às 00:20
#10932897
troyano escreveu: Tras sim,mas vc vai ter que aumentar um pouco a pressão da bomba !
E não almente muito os furos,0,5 mm é o suficiente !

Abraço !


Qual o real beneficio de se almentar os furos do vira?

E quanto a nitretação o amigo ja usou vale a pena?Ela almenta a durabilidade?Não seria a mesma coisa que pintar as peças como o molycote spray?O que indica fazer?

Por favor Entrar ou Registrar para participar da conversa.

Re: Retrabalho em Virabrequim

27/06/2009 às 13:59
#10932971
Pitoco... nao te conheço mas vou dar um conselho de amigo::(( acho que vc vai procurar sarna pra se coçar)) Mas,, como vc nao pediu meu conselho,, boa sorte na empreitada !! (y) (y)
[img



R O G É R I O
BRIGGO MOTORSPORT

Por favor Entrar ou Registrar para participar da conversa.

Re: Retrabalho em Virabrequim

27/06/2009 às 14:05
#10932977
Leva na Retifort, Retsam...la tem um trampo 10 !! Alívio e balanceamento !!!
"Em terra de saci todo chute é voadora"

Por favor Entrar ou Registrar para participar da conversa.

Re: Retrabalho em Virabrequim

27/06/2009 às 17:49
#10933029
Estou com um eixo de 1.8 balancedo std, porem tive problemas com uma biela e o casquilho rodou e tampou o canal de lubrificação ... desmontei tudo e pelo visto perdi a medida nesta biela ( o resto está zero). Como o eixo é balancedo estou com dó de abandoná-lo. Já ouvi falar em uma metlização que poderia devolver a medida std, alguem já utilizou algo parecido??

Valeu
saveiro turbo 1.9 "branquinha"

Por favor Entrar ou Registrar para participar da conversa.

Re: Retrabalho em Virabrequim

28/06/2009 às 22:34
#10933311
marciodesouzamsms escreveu:
troyano escreveu: Tras sim,mas vc vai ter que aumentar um pouco a pressão da bomba !
E não almente muito os furos,0,5 mm é o suficiente !

Abraço !


Qual o real beneficio de se almentar os furos do vira?

E quanto a nitretação o amigo ja usou vale a pena?Ela almenta a durabilidade?Não seria a mesma coisa que pintar as peças como o molycote spray?O que indica fazer?

Segue a dica do mestre Guy Croft!

Modificação nos furos de lubrificação do virabrequim:

A cross-drilled crank has oilways in main journals and cranlpins (rod journals) drilled right through the diameter, and the mains that feed the rods with oil from the high pressure feed in the crankcase are connected by a drilled gallery down through the crank web. Non cross-drilled cranks are cheaper and rely on just a diagonal drilling from main to crankpin.
The advantage of a cross-drilled crank is that you can more than one exit hole on the crankpin, offering superior lubrication.
But - to service a crossdrilled crank, you must unplug it because the outer radius region behaves like a centrifuge and collects dirty sludge from the oil, like this.
Any good race crank manufacturer will always cross-drilled. The position of the oilway on the crankpin is very critical, because if the bearing load is too high at the exit point, the oil pressure will be insufficient to let the oil out at all at main oil gallery delivery pressure.

The oilway mods shown in the photos have been done by me on virtually every crank I've ever prepped. The factory chamfer/radius on the drillings can vary from huge to OK to almost non-existent. I absolutely am sure that my preparing the journals in this way has contributed to the survivabality and reliabilty of GC engines over the years and is well worth doing. It takes time. An early crank like 131 2 liter which has 2 drillings per main journal compared with the later 2 (eg: Integrale) and is thru drilled on the crankpins (compared with the later ones which were only drilled to the centre) - takes me 3 hours or more. One slip iwith the tools and the crank is ruined.



2 liter Fiat TC crank - the sticky sludge traps particles from polishing, grinding & other crank mods, it can only be removed by unplugging the crank. All Fiat TC cranks are crossdrilled = race quality


Massive Vauxhall 2.3 liter 'HSR' crank below the Fiat 2 liter (arch enemies in world rally in the 70s, Chevette vs 131). The Vauxhall crank is not crossdrilled. Cheap, nasty, avoid.


Excellent drawing of a cross-drilled crank by member Jason Miller. Be careful when cleaning, the connecting drilling sometimes extends beyond the journal centreline.


GC mods to oilways. Keyhole helps entry of oil into crank and radius on crankpin (big-end journal) helps it disperse over bearing. Polish well. NO SHARP EDGES!


GC tap/plug op involves removing factory staked plugs in webs, threading at 7/16UNC (all three taps are needed plus tapping lubricant) and plugging as in crank at left


This is not GC prep and no way good enough for a finished crank, a quick 10 second attack with a carbide burr, devoid of radii and sharp edges, it will shred the bearings in no time.
PROJETO UNO 1.6R ASPIRADO/NITRO

Por favor Entrar ou Registrar para participar da conversa.

© 2026 www.HotCampinas.com - desde 1997