Perguntas [FOTO] Ford Falcon Coupe Xb 1973
[FOTO] Ford Falcon Coupe Xb 1973
04/05/2007 às 11:14
Quick Inspection: '73 XB Ford Falcon coupe
Powertrain
Engine: John Sidney Racing built the 400ci Dart Windsor stroker with 11.2:1-compression JE forged pistons, a 3.750-inch Scat crank, 6-inch Scat rods, Speed-Pro chrome-moly rings, Clevite 77 bearings, and ported Brodix heads with stainless valves (2.08/1.6 inches), bronze valveguides, Isky Gold springs, and titanium retainers. A Comp Cams solid roller cam with 0.697-inch lift, 264/268 duration (at 0.050) and a 106-degree lobe separation angle pushes Trend pushrods and actuates Comp Cams 1.6:1-ratio roller rockers. A Dick Johnson Racing dry-sump oil pan and pump keep the motor lubed, and an Edelbrock Victor Jr. intake manifold with a Holley HP-series 4150 830-cfm carb feeds it. Other details include an MSD billet distributor, a Meziere electric water pump, a Brown fuel pump, a surge tank, ceramic-coated 4-into-1 headers, and twin 3-inch stainless exhausts with a balance pipe.
Power: It makes 590 hp and 525 lb-ft at the flywheel.
Transmission: A Tremec TKO five-speed feeds power to a Ford 9-inch featuring Romac floating hubs, a 3.50 final drive ratio, and a limited-slip center.
It was decided during the build to remove all the flammable items from the cabin, which in turn necessitated getting the metal surfaces inside as smooth as the ones out. The dash was sectioned and rebuilt around the rollcage, and carbon-fiber and alloy panels replaced much of the trim. During the build, both the seating and steering position were tweaked for optimum ergonomics.Chassis
Suspension: Centreline Suspension-prepped, revalved Koni shocks are at all four corners, with 900-pound front springs, double reversed-eye rear leaves with a thicker main, a Watt's link, and urethane bushings. The front track was widened by 20 mm on each side for greater adjustability of camber, now allowing between -3 and -5 degrees and running 4 degrees caster.
Brakes: Race Brakes in Melbourne fit the 13.5-inch/13-inch front and rear custom brake kits that feature six- and four-piston AP Racing calipers, braided lines, Race Brakes RB74 pads, and a trick balance-bar arrangement with separate master cylinders for each end of the car.
Wheels/tires: Custom-made 17-inch Minilites were created by Harry Witham Racing to fit over the big brakes and measure 8 inches wide at the front and 9 inches out back, with 245/40 and 275/40 race rubber getting the power to the ground.
Style
Body: Steve Tupek put in 800 hours replacing and fabricating almost an entirely new body shell for the XB, taking time to get the panel gaps tight and making the new panels complete with press marks for more authenticity.
Paint: The color is PPG Bana Red inspired by the Coca-Cola Mustang that raced Bathurst in the late '60s. It's a conventional basecoat/clear application outside, while the interior and engine bay were painted in a one-step process in the same color.
Interior: The rear bulkhead and parcel tray were fabricated to seal the cabin from the trunk, with a trick GT logo embossed into the bulkhead. Steve mocked up interior panels in fiberglass before they were replicated in carbon fiber. John Taverna Chassis built the extensive rollcage that necessitated various modifications to the interior for clearance. Finally, the interior door handles were moved back 4 inches, and the factory indicator stalk was shortened by 1.5 inches.
Fotos:
BÔNUS - Papel de Parede:
Comentem...
(y)
Powertrain
Engine: John Sidney Racing built the 400ci Dart Windsor stroker with 11.2:1-compression JE forged pistons, a 3.750-inch Scat crank, 6-inch Scat rods, Speed-Pro chrome-moly rings, Clevite 77 bearings, and ported Brodix heads with stainless valves (2.08/1.6 inches), bronze valveguides, Isky Gold springs, and titanium retainers. A Comp Cams solid roller cam with 0.697-inch lift, 264/268 duration (at 0.050) and a 106-degree lobe separation angle pushes Trend pushrods and actuates Comp Cams 1.6:1-ratio roller rockers. A Dick Johnson Racing dry-sump oil pan and pump keep the motor lubed, and an Edelbrock Victor Jr. intake manifold with a Holley HP-series 4150 830-cfm carb feeds it. Other details include an MSD billet distributor, a Meziere electric water pump, a Brown fuel pump, a surge tank, ceramic-coated 4-into-1 headers, and twin 3-inch stainless exhausts with a balance pipe.
Power: It makes 590 hp and 525 lb-ft at the flywheel.
Transmission: A Tremec TKO five-speed feeds power to a Ford 9-inch featuring Romac floating hubs, a 3.50 final drive ratio, and a limited-slip center.
It was decided during the build to remove all the flammable items from the cabin, which in turn necessitated getting the metal surfaces inside as smooth as the ones out. The dash was sectioned and rebuilt around the rollcage, and carbon-fiber and alloy panels replaced much of the trim. During the build, both the seating and steering position were tweaked for optimum ergonomics.Chassis
Suspension: Centreline Suspension-prepped, revalved Koni shocks are at all four corners, with 900-pound front springs, double reversed-eye rear leaves with a thicker main, a Watt's link, and urethane bushings. The front track was widened by 20 mm on each side for greater adjustability of camber, now allowing between -3 and -5 degrees and running 4 degrees caster.
Brakes: Race Brakes in Melbourne fit the 13.5-inch/13-inch front and rear custom brake kits that feature six- and four-piston AP Racing calipers, braided lines, Race Brakes RB74 pads, and a trick balance-bar arrangement with separate master cylinders for each end of the car.
Wheels/tires: Custom-made 17-inch Minilites were created by Harry Witham Racing to fit over the big brakes and measure 8 inches wide at the front and 9 inches out back, with 245/40 and 275/40 race rubber getting the power to the ground.
Style
Body: Steve Tupek put in 800 hours replacing and fabricating almost an entirely new body shell for the XB, taking time to get the panel gaps tight and making the new panels complete with press marks for more authenticity.
Paint: The color is PPG Bana Red inspired by the Coca-Cola Mustang that raced Bathurst in the late '60s. It's a conventional basecoat/clear application outside, while the interior and engine bay were painted in a one-step process in the same color.
Interior: The rear bulkhead and parcel tray were fabricated to seal the cabin from the trunk, with a trick GT logo embossed into the bulkhead. Steve mocked up interior panels in fiberglass before they were replicated in carbon fiber. John Taverna Chassis built the extensive rollcage that necessitated various modifications to the interior for clearance. Finally, the interior door handles were moved back 4 inches, and the factory indicator stalk was shortened by 1.5 inches.
Fotos:
BÔNUS - Papel de Parede:
Comentem...
(y)
Por favor Entrar ou Registrar para participar da conversa.
Re: INTERCEPTOR DO MAD MAX
04/05/2007 às 12:44
O carro do Mad Max era exatamente esse, vejam só:
www.madmaxmovies.com/cars/interceptor/history1.html
www.madmaxmovies.com/cars/interceptor/history1.html
Golf GTi 2005 ex-180HP atual 225HP by 1.2Bar e "mods"
Yamaha YZF-R1 2004 preta "BANDIDA"
Yamaha YZF-R1 2004 preta "BANDIDA"
Por favor Entrar ou Registrar para participar da conversa.
Re: Re: INTERCEPTOR DO MAD MAX
04/05/2007 às 13:12ParatiGTi escreveu: O carro do Mad Max era exatamente esse, vejam só:
www.madmaxmovies.com/cars/interceptor/history1.html
Realmente, era um falcon tanto o interceptor quanto os pursuits!!!!!!!
Lah na australia esse carro eh igual ao maverick aki!!!!!!!! Show
Por favor Entrar ou Registrar para participar da conversa.