Perguntas AJUDA COM PISTÃO JE 83mm
Re: AJUDA COM PISTÃO JE 83mm
24/04/2012 às 23:10stdvw escreveu: caraca de 17 a 21 de folga de pistao :eek: rapaisss nunca vi isso 8O
DA UMA FUÇADA QUE VC VAI ACHAR , O PISTAO É DA MARCA VENOLIA I NESSE CASO É PARA OPALA 6CC .
NO MANUAL TEM ALGO A GROSSO MODO ASSIM :
TURBO EXTREMO E TURBO NITRO 17 A 21 .
ESSE PISTÃO ESTA COM MEU AMIGO A NO MINIMO UNS 15 ANOS (O CARA É TEIMOSO , NAO DESISTE DE JEITO NENHUM DE MONTAR ESSE OPALA ) É QUE NAO TEM R$ QUE CHEGUE , MAS ESTA NOS FINALMENTE AGORA .
QUANDO ELE PEGOU ESSES PISTOES TAMBEM NAO ENTENDEU NADA FALO QUE PORRA É ESSA , AI FOI ATÉ UM COLEGA O ADRIANO DA BPM QUE ULTILIZAVA SEMPRE ESSA MARCA E O MESMO DISSE "É ISSO AI MESMO" .
NA DUVIDA ? APOSTE SEMPRE NO AP !
Por favor Entrar ou Registrar para participar da conversa.
Re: AJUDA COM PISTÃO JE 83mm
24/04/2012 às 23:19
OLHA OQUE ELES RECOMENDAM PARA OS PISTOES ATUAIS .
PISTON CLEARANCE: With 2618 alloy, top of skirt .008 to .010. Bottom of skirt: .005 to .007". Air cooled engines usually require more clearance.
Check your pistons completely for any burrs or sharp edges. Using a deburring knife, lightly go over any sharp edges. Make sure there are no chips in the ring lands and pin locks left from machining operations. Thoroughly clean the pistons in solvent and blow them dry with a high-powered air hose.
Check all rings in their respective bores for proper end gap clearance. It is best to use a ring squaring tool to make sure the rings are square in the bore before measuring end gaps. Make sure you use a commercial ring filer to increase the end gaps and that it cuts the rings square.
RING CLEARANCE: Side Clearance .003 to .004 ring gap: .004 to .005 per inch of bore.
When fitting rings to cylinder bores, every .001" change in bore diameter changes the end gap by approximately .003." Diameter changes affect the gap by the factor of Pi 3.1416. An example of an increase in bore diameter of .002" increases the ring gap by .00628.
Example: .002 x 3.1416 = .00628
www.venolia.com
PISTON CLEARANCE: With 2618 alloy, top of skirt .008 to .010. Bottom of skirt: .005 to .007". Air cooled engines usually require more clearance.
Check your pistons completely for any burrs or sharp edges. Using a deburring knife, lightly go over any sharp edges. Make sure there are no chips in the ring lands and pin locks left from machining operations. Thoroughly clean the pistons in solvent and blow them dry with a high-powered air hose.
Check all rings in their respective bores for proper end gap clearance. It is best to use a ring squaring tool to make sure the rings are square in the bore before measuring end gaps. Make sure you use a commercial ring filer to increase the end gaps and that it cuts the rings square.
RING CLEARANCE: Side Clearance .003 to .004 ring gap: .004 to .005 per inch of bore.
When fitting rings to cylinder bores, every .001" change in bore diameter changes the end gap by approximately .003." Diameter changes affect the gap by the factor of Pi 3.1416. An example of an increase in bore diameter of .002" increases the ring gap by .00628.
Example: .002 x 3.1416 = .00628
www.venolia.com
NA DUVIDA ? APOSTE SEMPRE NO AP !
Por favor Entrar ou Registrar para participar da conversa.
Re: AJUDA COM PISTÃO JE 83mm
25/04/2012 às 01:04
ja vi gente falando q monta JE com quase 15 de folga, mas falar ate papagaio fala né?!? .qnto aos aneis, os total seal duram menos, mas nao acho q seja nada tao preocupante
Gol S 1985 verde esmeralda 1.9T
Por favor Entrar ou Registrar para participar da conversa.
Re: AJUDA COM PISTÃO JE 83mm
25/04/2012 às 01:32
Amigo pistão JE p/ AP a folga recomendada é de 0,10 a 0,14 depende do uso, os anéis vc precisa saber qual é a medida das canaletas, dá p/ adaptar anéis de moto sem problema nenhum (y)
FERRETTO MOTORES
NEXTEL 130*15000
NEXTEL 130*15000
Por favor Entrar ou Registrar para participar da conversa.