Perguntas POR QUE 3¨ de ALTURA NA ARRANCADA ?
Re: POR QUE 3¨ de ALTURA NA ARRANCADA ?
05/04/2008 às 17:43
Quem quiser ficar por dentro do Rule Book da NHRA SportCompact de 2007 como exemplo ta ai em PDF:
Introduction - 2.3 MB
www.nhrasportcompact.com/2007/rules/intro2007.pdf
General regulations - 1 MB
www.nhrasportcompact.com/2007/rules/GenRegs2007.pdf
Class regulations - 1.2 MB
www.nhrasportcompact.com/2007/rules/ClassRegs2007.pdf
Complete rulebook (zip file for download only) - 1.8 MB
www.nhrasportcompact.com/2007/rules/2007rules.zip
As revisões p/ 2008 são essas:
2008 NHRA sanctioned sport compact rulebook
Revisions
Last Update 03/19/2008
General Regulations
Section 1:3 – Exhaust
Remove “Unlimited Street” from the fourth sentence of the first paragraph
Section 1:16 – Vent Tubes, Breathers
Add the following to the end of the second sentence in the first paragraph:
for 8-cylinder applications and 2.5 quarts for all other applications.
Quick 16
The Quick 16 Class is designed to showcase the 16 quickest cars at an event that may not be eligible for any of the heads-up classes and provides an alternative to standard E.T. bracket racing classes for these competitors. This class will be run as a 5 tenths full tree, dial your own, handicapped start.
The class features a 16-car qualified field. Cars are qualified based on e.t., from quickest to slowest. Vehicles must run 11.49 or quicker to be eligible for competition. (Non-qualifiers may move to E.T. Brackets eliminations.)
First-round eliminations are based on a 16-car Sportsman ladder, where the No. 1 qualifier competes against No. 9, No. 2 against No. 10, and so on until No. 8 competes against No. 16.
Technical rules and regulations are the same as for E.T. Brackets, based upon actual vehicle performance.
Engine Containment Device: Engine diaper or catch-pan device to capture oil and debris in event of engine failure mandatory. Where exhaust header passes directly under oil pan, two-piece diaper may be utilized. FWD vehicles using OEM manual transmission case must also have such a device for the transmission, to capture oil and debris in event of transmission failure. If catch-pan device is used, catch pan must employ minimum 2-inch-high lips on all sides. Lips must be coved or curved inward, so as to contain oil in pan. Catch pan must cover entire area below engine/transmission. Catch pan must extend from radiator support to firewall and from framerail to framerail. In all cases, lips must be adequate enough to contain oil in the catch pan. Should a competitor spill excessive oil from the catch pan and debris onto the track, he or she may be disqualified from further competition at the sole and absolute discretion of the event director until catch pan is upgraded, regardless of height of pan lips or pan design.
All competitors must have competition number and membership number. Valid NHRA competition license mandatory for driver of any vehicle running 9.99 or quicker or 135 mph or faster. All drivers running 10.00 seconds or slower must have a valid state- or government-issued driver's license beyond a learner's-permit level or valid NHRA competition license. See General Regulations 10:4.
ET Brackets
Engine
Replace the second sentence of the first paragraph with the following:
RWD platform: Any 4-, 6- or 8-cylinder automobile engine, import or domestic, permitted.
PURE STREET
Designation
P/S preceded by car number.
Sport Compact FWD 4 and 6 cylinder cars only. Unibody chassis, all glass, full interior, drag slick class, motor swaps allowed.
Minimum Weights
Class Minimum weight: 2,000 pounds
FWD 4-cylinder (D – Series): 2,000 pounds
FWD 4-cylinder (B – Series): 2,050 pound
FWD 4-cylinder (F – Series; single cam): 2,050 pounds
FWD 4-cylinder (F – Series; twin cam): 2,200 pounds
FWD 4-cylinder (H – Series): 2,100 pounds
FWD 4-cylinder (K – Series): 2,200 pounds
FWD 6-cylinder: 2,400 pounds
Add 50 pounds to entries with dog box transmissions.
Add 50 pounds to cars with ITB set ups.
All weights include driver, verified after the run.
CLASS REQUIREMENTS
Engine
Naturally aspirated entries limited to 3.0 liters. Engine must be from the same manufacturer as body. Bolt on modifications only. Internal modifications permitted.
Cylinder Head
Aftermarket cams, valves, cam gears, porting, polishing, welding, and epoxying permitted; must be commercially available with a minimum production run of 500.
Induction System
Must be commercially available. Individual throttle bodies permitted.
Engine Containment Device
Engine diaper or catch-pan device to capture oil and debris in event of engine failure mandatory. Where exhaust header passes directly under oil pan, two-piece diaper may be utilized. FWD vehicles using OEM manual-transmission case must also have such a device for the transmission, to capture oil and debris in event of transmission failure. If catch-pan device is used, catch pan must employ minimum 2-inch-high lips on all sides. Lips must be coved or curved inward, so as to contain oil in pan. Catch pan must cover entire area below engine/transmission. Catch pan must extend from radiator support to firewall and from framerail to framerail. In all cases, lips must be adequate enough to contain oil in the catch pan. Should a competitor spill excessive oil from the catch pan and debris onto the track, he or she may be disqualified from further competition at the sole and absolute discretion of the event director until catch pan is upgraded, regardless of height of pan lips or pan design.
Exhaust
All exhaust must flow through functioning muffler(s); must exit in OEM location. Any vehicle that did not come equipped with a muffler(s) from the factory permitted, provided complete, unmodified (except for header) OEM exhaust system is utilized. See General Regulations 1:3.
Fuel
NHRA-accepted racing gasoline, gasoline (including E85), diesel,
natural gas, and propane permitted. All other fuels prohibited. See
General Regulations 2:12.
Fuel System
Fuel cell allowed. All cars must be equipped with a drain valve located on return side of fuel rail to facilitate removal of fuel samples for fuel-check purposes. See General Regulations 1:5.
Liquid Overflow
See General Regulations 1:6.
Flywheel Shield
All cars using a clutch and running quicker than 11.49 or faster than 135 mph must be equipped with a flywheel shield made of 1/4-inch-minimum-thickness steel plate. Shield must surround the bellhousing completely except for area of flywheel shield adjacent
to differential and axle shaft. Shield may be multi-piece with pieces bolted together using minimum 3/8-inch-diameter Grade 5 or M10 class 8.8 bolts; may be attached to engine and/or bellhousing. In lieu of shield, a blanket meeting SFI Spec 4.1, completely surrounding the bellhousing, is permitted. See General Regulations 2:5, 2:6, 2:9, 2:10.
Transmission, Automatic
Transmission must be OEM for engine used. All cars using an automatic transmission and running quicker than 10.99 or faster than 135 mph must be equipped with a transmission shield meeting SFI Spec 4.1, a flexplate shield labeled as meeting SFI
Spec 30.1, and a flexplate labeled as meeting SFI Spec 29.1. Transmission brake prohibited.
Transmission, Manual
Transmission must be OEM for engine used. Automated, timertype, pneumatic, electric, electronic, hydraulic, etc. shifting mechanism prohibited; each individual shift must be a function of the driver and controlled manually. (Driver must pull the lever.) Transmission adapter permitted provided adapter plate is approved by NHRA in advance.
Approved transmission adapters: Part No. 26008: Evolution H2B kit without mounts; Part No. 26208: Evolution H2B kit with mounts; Part No. 26308: Evolution/Bisimoto kit without mounts; Part No. 25208: Evolution/Bisimoto kit with mounts; Part No. 26509: Evolution/Bisimoto H2D kit without mounts; Quartersports Racing H2B Kit.
Brakes
Four-wheel hydraulic brakes mandatory. Carbon fiber brake rotors prohibited.Staging brake prohibited. See General Regulations 3:1.
Steering
Must retain full, original OEM steering gear. See General Regulations 3:2, 3:3, 4:1.
Suspension, Front
Complete, operative OEM suspension mandatory. Solid OEM replacement mounting bushings allowed. Bolt-on traction devices permitted. Control arms, strut mounting points, etc. must be OEM, front and rear. Aftermarket springs and struts, including coil-overs, permitted, but must utilize original OEM mounting points. Final decision rests with NHRA Technical Services.
Suspension, Rear
Strut tower braces, lower tie bars, sway bars, and limit straps are permitted. Complete, operative OEM suspension mandatory. Bolton traction devices permitted. Control arms, strut mounting points, etc. must be OEM, front and rear. Aftermarket control arms, springs and struts, including coil-overs, permitted, but must utilize original OEM mounting points. Final decision rests with NHRA Technical Services. Spindle mounts
prohibited.
Wheelie Bars
Prohibited.
Ballast
Permitted. See General Regulations 4:2.
Chassis
OEM chassis, with complete OEM floorpan and firewall, mandatory. Wheel tubs, back-half conversions, tube chassis, etc. prohibited. Rear bumper supports may be removed. Must retain FWD configuration; rear-drive conversions prohibited. Engine must be located in OEM location for body used. Roll bar mandatory in any car running 11.49
or quicker; roll cage mandatory in any car running 9.99 or quicker or 135 mph or faster. Non-OEM tubing in front of firewall prohibited except to tie shock towers to roll cage. Roll cage in cars running 9.99 or quicker must be inspected every three years by NHRA and have serialized sticker affixed to roll cage before participation. See General Regulations 4:10, 4:11, 10:6.
Ground Clearance
Minimum 3 inches from front of car to 12 inches behind centerline of front axle, 2 inches for remainder of car (except for exhaust more than 12 inches behind centerline of front axle).
Parachute
Mandatory on any car running 150 mph or faster. See General Regulations 4:8.
Wheelbase
Must retain original wheelbase for body used, plus or minus 1 inch. Maximum wheelbase variation from left to right is 1 inch.
Tires
All applications limited to a maximum width of 9.0 inches and maximum height of 25.0 inches; DOT or racing slicks permitted. Rear skinnies permitted. Retreads, space-saver spares, or any other non-DOT-approved tire prohibited.
Wheels
Must be automotive-type wheels suitable for street or racing use. Minimum wheel size 13 inches unless originally equipped with smaller wheels and vehicle is equipped with original engine. Wheel studs must be threaded into hex portion of lug nut a distance at
least equal to the diameter of the stud. Spindle mounts prohibited. See General Regulations 5:2.
Interior
Complete interior, including dashboard, door panels, headliner, etc. mandatory. Rear seat may be removed, but all other upholstery and panels must remain in place. Two matching, upholstered front seats mandatory. Aftermarket seats permitted, but must be fully upholstered. All factory controls must be retained and operative; i.e., lights, signals, horn, windows, and wipers.
Body
Body must be on NHRA Accepted Bodies list. Pickup and SUV bodies prohibited.
Complete, OEM body structure mandatory, including floorpan, firewall, strut towers, wheel houses, etc. Chopped roofs prohibited. Mild customizing body kits permitted, but must retain full-bodied appearance, with minimum two functional doors. Doors must open and close from inside and outside. Windshield and all windows must retain OEM safety glass.
Lightweight body panels limited to hood and hatch or deck lid. Air inlet may not extend past the front bumper. Aftermarket body kits permitted, but full street-legal appearance must be maintained. One-piece aftermarket front end prohibited.
NHRA-approved front ends : JCR-EG3 (92-95 Civic); JCR-EKS (99-00 Civic); JCR-EF3 (88-91 CRX) and JCR-DC3 (98-00 Integra).
Competition Numbers
See General Regulations 7:2.
Firewall
OEM firewall mandatory. See General Regulations 6:1, 7:4.
Floor
OEM floorpan, front to rear, mandatory.
Street Equipment
Windshield wipers and OEM side mirrors mandatory. Complete headlight and taillight assemblies (all) mandatory; must be operative.
Windshield/Windows
Complete OEM windshield and windows mandatory. Windows must be operative per factory specifications. (Must open and close via electrical or OEM mechanical means.)
Batteries
Batteries must be securely mounted; may not be located in driver compartment unless sealed off per General Regulations. OEM 12- volt system mandatory. 16-volt b atteries/electrical system prohibited. See General Regulations 8:1.
Ignition
Two steps, rev limiters, etc. permitted. See General Regulations 8:1, 8:3, 8:4, 8:5.
Master Cutoff
Mandatory on any car running 9.99 or quicker, or 135 mph or faster, or on any car where battery is relocated to trunk area of vehicle. See General Regulations 8:4.
Computer
Prohibited. See General Regulations 9:1.
Data Recorder
Permitted. See General Regulations 9:2.
Fire Extinguisher System
Permitted; must be securely mounted. See General Regulations 9:3.
Two Vehicles
Prohibited.
Warm-Ups
See General Regulations 9:4, 9:12.
Credentials
All competitors must have competition number and membership number. Valid NHRA competition license mandatory for driver of any vehicle running 9.99 or quicker or 135 mph or faster. All drivers running 10.00 seconds or slower must have a valid state- or
government-issued driver's license beyond a learner's-permit level or valid NHRA competition license. See General Regulations 10:4.
Driver Restraint System
Three-inch-wide driver restraint system labeled as meeting SFI Spec 16.1 mandatory in any car required to have a roll bar or roll cage. System includes crotch strap and must be updated at twoyear intervals from date of manufacture. All other cars, OEM restraint system mandatory. See General Regulations 10:5, 10:11.
Helmet
Helmet meeting Snell K98, 2000, 2005 or SFI Spec 31.1A, 31.2A, 31.1/2005, 41.1A, 41.2A, or 41.1/2005 mandatory. Effective Jan. 1, 2008, full-face helmet mandatory on all cars 9.99 or quicker. See General Regulations 10:7.
Neck Collar
Mandatory on driver of any car running 9.99 seconds or quicker or 135 mph or faster. See General Regulations 10:8.
Protective Clothing
See General Regulations 10:10.
Power Street
Designation
Remove the following from the first paragraph second sentence:
Slicks allowed on naturally aspirated entries.
Engine
Remove the following from the first paragraph first sentence:
Naturally aspirated entries limited to 2.5 liters.
Tires
Replace the first paragraph with the following:
AWD and RWD 4-cyl forced induction applications, maximum tire size 245/60, NHRA/DOT approved radial tires only. FWD 4- and 6-cylinder applications, maximum tires size 235/60, NHRA/DOT approved tires permitted, racing slicks prohibited. Rear “skinnies” prohibited on all forced induction applications. Retreads, space-savers spares, or any non DOT-approved tire prohibited.
Power Street FWD NHRA/DOT-approved Tire List
Part # Nominal Size
MT
3752 10.5” by 26.1”
Hoosier
17410 9.3” by 26.1”
17400 9.5” by 26.1”
17430 9.3” by 26.1”
M and H
MHD-01 10.5” by 26”
MSS-008 9.8” by 25.4”
Replace the title of the approved tire list to:
NHRA/DOT-approved Radial Tires for AWD/RWD Applications
Remove the following from the title
(maximum rollout on drive tires 84 inches)
Turbo Street
Designations
Remove the following from this section:
Valid DOT registration and license plates mandatory.
Turbocharger
Replace the second paragraph with the following:
K-Series and Ecotec turbo applications limited to a maximum 67.8mm (2.669 inches) where the maximum compressor wheel diameter may not exceed 67.88 mm (2.672 inches) measured at the point where the leading edge of the compressor wheel meets
the housing; the compressor housing inducer diameter may not exceed 69.13mm (2.722 inches) measured at the point where the leading edge of the compressor wheel meets the housing. Compressor wheel inducer contours of wheel may not be stepped, notched, or clipped; e.g., the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing is prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic material wheels prohibited.
Tires
Please add the following “Accepted Tire List for AWD/RWD Four-Cylinder Applications” to this section:
Mickey Thompson
Type Part Number
DOT 3792
Slick 3052
Hoosier Tire
Type Part Number
DOT 17430
Slick 18120
Toyo Tires
Type Part Number
Slick 370210
Slick 370230
Body
Add the following to the end of the third paragraph:
NHRA-approved front ends : JCR-EG3 (92-95 Civic); JCR-EKS (99-00 Civic); JCR-EF3 (88-91 CRX) and JCR-DC3 (98-00 Integra).
Unlimited Street
Designations
Remove the following from this section:
Valid DOT registration and license plates mandatory.
Minimum Weights
Add the following to this section:
RWD 6-cylinder (1 or 2 power adders)
3.51 to 4.0 liter (214.19 to 2.44.09 cid) 3,350 pounds
Add the following to this section
Nitrous Oxide (364 ci) 3,125 pounds
(365 ci to 400 ci, add 5 pounds per cubic inch)
Exhaust
Replace this section with the following:
All cars competing in Unlimited Street may be required to run with functioning muffler(s) depending on track regulations. See General Regulations 1:3.
Supercharger
Add the following to the Unlimited Street Approved Supercharger list:
Kenne Bell Blowers 1.5L/1.7L/2.1L/2.2L/2.4L/2.6L/2.8L
Big Bore Kits Flowzilla
Blowzilla
Magnacharger Blowers MP45/MP62/MP90/MP112 4th and 5th Gen.
Whipple Blowers W140AX/W200AX/W200R/W305AX/W305R
Ford Motorsports Blowers 2.2L/3.4L/4.6L
Turbocharger
Replace the first paragraph in this section with the following
Eight-cylinder, single turbo applications limited to a maximum 80 mm (3.150 inches) where the maximum compressor wheel diameter may not exceed 80.5 mm (3.169 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 81.75 mm (3.219 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Replace “Four-cylinder, single turbo” in the second paragraph with “Four-cylinder and Six-cylinder (3.51 to 4.0 liter), single turbo”
Add the following paragraph to this section:
Eight-cylinder, twin turbo applications limited to a maximum 66 mm (2.598 inches) where the maximum compressor wheel diameter may not exceed 66.5 mm (2.618 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 67.75 mm (2.667 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph to this section:
Six-cylinder (3.51 to 4.0 liter), twin turbo applications limited to a maximum 68 mm (2.677 inches) where the maximum compressor wheel diameter may not exceed 68.5 mm (2.697 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 69.75 mm (2.746 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Transmission
Add the following new paragraph after the first paragraph
Approved transmission adapters: MAZ-10150; MAZ-10151; MAZ-10155 and MAZ-10156
Chassis
Add the following after the first sentence in the first paragraph:
Mini-tubes permitted on drag radial combinations only.
Battery
Replace this section with the following:
Batteries must be securely mounted; may not be located in driver compartment unless sealed off per General Regulations. See General Regulations 8:1.
Modified
Engine
Add the following to the end of this section:
8-cylinder applications limited to 449 ci maximum displacement.
Turbocharger
Replace “Two-rotor and four-cylinder, single turbo” in the first sentence of the fifth paragraph with “Two-rotor, three-rotor and four-cylinder, single turbo”
Replace the seventh paragraph in this section with the following:
Eight-cylinder, single turbo applications limited to a maximum 96 mm (3.779 inches) where the maximum compressor wheel diameter may not exceed 96.5 mm (3.799 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 97.75 mm (3.848 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Replace the eighth paragraph in this section with the following:
Eight-cylinder, twin turbo applications limited to a maximum 78 mm (3.071 inches) where the maximum compressor wheel diameter may not exceed 78.5 mm (3.091 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 78.75 mm (3.100 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph to this section:
Two- and three- rotor, twin turbo applications limited to a maximum 61 mm (2.401 inches) where the maximum compressor wheel diameter may not exceed 61.5 mm (2.421 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 62.75 mm (2.470 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Pro FWD
Minimum Weights
Add the following weight break
3RZ-FE (1 power adder only) 2,100 pounds
Turbocharger
Add the following paragraph below the Four-cylinder, single-turbo section:
3RZ-FE single turbo, applications limited to a maximum 95 mm (3.740 inches) where the maximum compressor wheel diameter may not exceed 75.5 mm (3.759 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 96.75 mm (3.809 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Pro RWD
Turbocharger
Replace the third paragraph with the following:
JZ and FZ series engines, single turbo applications limited to a maximum 88 mm (3.465 inches) where the maximum compressor wheel diameter may not exceed 88.5 mm (3.484 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 89.75 mm (3.533 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph after the JZ and FZ series engines, single turbo section
FZ and JZ series engines, twin turbo applications limited to a maximum 66 mm (2.984 inches) where the maximum compressor wheel diameter may not exceed 66.5 mm (2.618 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 67.75 mm (2.667 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Wheelie Bar
Replace the second sentence of the first paragraph with the following
Maximum length of 75 inches for 4- and 6- cylinder applications and 85 inches for 8- cylinder applications.
Body
Replace the first paragraph with the following:
Body must be on NHRA Accepted Bodies list. Pickup and SUV bodies prohibited.
Introduction - 2.3 MB
www.nhrasportcompact.com/2007/rules/intro2007.pdf
General regulations - 1 MB
www.nhrasportcompact.com/2007/rules/GenRegs2007.pdf
Class regulations - 1.2 MB
www.nhrasportcompact.com/2007/rules/ClassRegs2007.pdf
Complete rulebook (zip file for download only) - 1.8 MB
www.nhrasportcompact.com/2007/rules/2007rules.zip
As revisões p/ 2008 são essas:
2008 NHRA sanctioned sport compact rulebook
Revisions
Last Update 03/19/2008
General Regulations
Section 1:3 – Exhaust
Remove “Unlimited Street” from the fourth sentence of the first paragraph
Section 1:16 – Vent Tubes, Breathers
Add the following to the end of the second sentence in the first paragraph:
for 8-cylinder applications and 2.5 quarts for all other applications.
Quick 16
The Quick 16 Class is designed to showcase the 16 quickest cars at an event that may not be eligible for any of the heads-up classes and provides an alternative to standard E.T. bracket racing classes for these competitors. This class will be run as a 5 tenths full tree, dial your own, handicapped start.
The class features a 16-car qualified field. Cars are qualified based on e.t., from quickest to slowest. Vehicles must run 11.49 or quicker to be eligible for competition. (Non-qualifiers may move to E.T. Brackets eliminations.)
First-round eliminations are based on a 16-car Sportsman ladder, where the No. 1 qualifier competes against No. 9, No. 2 against No. 10, and so on until No. 8 competes against No. 16.
Technical rules and regulations are the same as for E.T. Brackets, based upon actual vehicle performance.
Engine Containment Device: Engine diaper or catch-pan device to capture oil and debris in event of engine failure mandatory. Where exhaust header passes directly under oil pan, two-piece diaper may be utilized. FWD vehicles using OEM manual transmission case must also have such a device for the transmission, to capture oil and debris in event of transmission failure. If catch-pan device is used, catch pan must employ minimum 2-inch-high lips on all sides. Lips must be coved or curved inward, so as to contain oil in pan. Catch pan must cover entire area below engine/transmission. Catch pan must extend from radiator support to firewall and from framerail to framerail. In all cases, lips must be adequate enough to contain oil in the catch pan. Should a competitor spill excessive oil from the catch pan and debris onto the track, he or she may be disqualified from further competition at the sole and absolute discretion of the event director until catch pan is upgraded, regardless of height of pan lips or pan design.
All competitors must have competition number and membership number. Valid NHRA competition license mandatory for driver of any vehicle running 9.99 or quicker or 135 mph or faster. All drivers running 10.00 seconds or slower must have a valid state- or government-issued driver's license beyond a learner's-permit level or valid NHRA competition license. See General Regulations 10:4.
ET Brackets
Engine
Replace the second sentence of the first paragraph with the following:
RWD platform: Any 4-, 6- or 8-cylinder automobile engine, import or domestic, permitted.
PURE STREET
Designation
P/S preceded by car number.
Sport Compact FWD 4 and 6 cylinder cars only. Unibody chassis, all glass, full interior, drag slick class, motor swaps allowed.
Minimum Weights
Class Minimum weight: 2,000 pounds
FWD 4-cylinder (D – Series): 2,000 pounds
FWD 4-cylinder (B – Series): 2,050 pound
FWD 4-cylinder (F – Series; single cam): 2,050 pounds
FWD 4-cylinder (F – Series; twin cam): 2,200 pounds
FWD 4-cylinder (H – Series): 2,100 pounds
FWD 4-cylinder (K – Series): 2,200 pounds
FWD 6-cylinder: 2,400 pounds
Add 50 pounds to entries with dog box transmissions.
Add 50 pounds to cars with ITB set ups.
All weights include driver, verified after the run.
CLASS REQUIREMENTS
Engine
Naturally aspirated entries limited to 3.0 liters. Engine must be from the same manufacturer as body. Bolt on modifications only. Internal modifications permitted.
Cylinder Head
Aftermarket cams, valves, cam gears, porting, polishing, welding, and epoxying permitted; must be commercially available with a minimum production run of 500.
Induction System
Must be commercially available. Individual throttle bodies permitted.
Engine Containment Device
Engine diaper or catch-pan device to capture oil and debris in event of engine failure mandatory. Where exhaust header passes directly under oil pan, two-piece diaper may be utilized. FWD vehicles using OEM manual-transmission case must also have such a device for the transmission, to capture oil and debris in event of transmission failure. If catch-pan device is used, catch pan must employ minimum 2-inch-high lips on all sides. Lips must be coved or curved inward, so as to contain oil in pan. Catch pan must cover entire area below engine/transmission. Catch pan must extend from radiator support to firewall and from framerail to framerail. In all cases, lips must be adequate enough to contain oil in the catch pan. Should a competitor spill excessive oil from the catch pan and debris onto the track, he or she may be disqualified from further competition at the sole and absolute discretion of the event director until catch pan is upgraded, regardless of height of pan lips or pan design.
Exhaust
All exhaust must flow through functioning muffler(s); must exit in OEM location. Any vehicle that did not come equipped with a muffler(s) from the factory permitted, provided complete, unmodified (except for header) OEM exhaust system is utilized. See General Regulations 1:3.
Fuel
NHRA-accepted racing gasoline, gasoline (including E85), diesel,
natural gas, and propane permitted. All other fuels prohibited. See
General Regulations 2:12.
Fuel System
Fuel cell allowed. All cars must be equipped with a drain valve located on return side of fuel rail to facilitate removal of fuel samples for fuel-check purposes. See General Regulations 1:5.
Liquid Overflow
See General Regulations 1:6.
Flywheel Shield
All cars using a clutch and running quicker than 11.49 or faster than 135 mph must be equipped with a flywheel shield made of 1/4-inch-minimum-thickness steel plate. Shield must surround the bellhousing completely except for area of flywheel shield adjacent
to differential and axle shaft. Shield may be multi-piece with pieces bolted together using minimum 3/8-inch-diameter Grade 5 or M10 class 8.8 bolts; may be attached to engine and/or bellhousing. In lieu of shield, a blanket meeting SFI Spec 4.1, completely surrounding the bellhousing, is permitted. See General Regulations 2:5, 2:6, 2:9, 2:10.
Transmission, Automatic
Transmission must be OEM for engine used. All cars using an automatic transmission and running quicker than 10.99 or faster than 135 mph must be equipped with a transmission shield meeting SFI Spec 4.1, a flexplate shield labeled as meeting SFI
Spec 30.1, and a flexplate labeled as meeting SFI Spec 29.1. Transmission brake prohibited.
Transmission, Manual
Transmission must be OEM for engine used. Automated, timertype, pneumatic, electric, electronic, hydraulic, etc. shifting mechanism prohibited; each individual shift must be a function of the driver and controlled manually. (Driver must pull the lever.) Transmission adapter permitted provided adapter plate is approved by NHRA in advance.
Approved transmission adapters: Part No. 26008: Evolution H2B kit without mounts; Part No. 26208: Evolution H2B kit with mounts; Part No. 26308: Evolution/Bisimoto kit without mounts; Part No. 25208: Evolution/Bisimoto kit with mounts; Part No. 26509: Evolution/Bisimoto H2D kit without mounts; Quartersports Racing H2B Kit.
Brakes
Four-wheel hydraulic brakes mandatory. Carbon fiber brake rotors prohibited.Staging brake prohibited. See General Regulations 3:1.
Steering
Must retain full, original OEM steering gear. See General Regulations 3:2, 3:3, 4:1.
Suspension, Front
Complete, operative OEM suspension mandatory. Solid OEM replacement mounting bushings allowed. Bolt-on traction devices permitted. Control arms, strut mounting points, etc. must be OEM, front and rear. Aftermarket springs and struts, including coil-overs, permitted, but must utilize original OEM mounting points. Final decision rests with NHRA Technical Services.
Suspension, Rear
Strut tower braces, lower tie bars, sway bars, and limit straps are permitted. Complete, operative OEM suspension mandatory. Bolton traction devices permitted. Control arms, strut mounting points, etc. must be OEM, front and rear. Aftermarket control arms, springs and struts, including coil-overs, permitted, but must utilize original OEM mounting points. Final decision rests with NHRA Technical Services. Spindle mounts
prohibited.
Wheelie Bars
Prohibited.
Ballast
Permitted. See General Regulations 4:2.
Chassis
OEM chassis, with complete OEM floorpan and firewall, mandatory. Wheel tubs, back-half conversions, tube chassis, etc. prohibited. Rear bumper supports may be removed. Must retain FWD configuration; rear-drive conversions prohibited. Engine must be located in OEM location for body used. Roll bar mandatory in any car running 11.49
or quicker; roll cage mandatory in any car running 9.99 or quicker or 135 mph or faster. Non-OEM tubing in front of firewall prohibited except to tie shock towers to roll cage. Roll cage in cars running 9.99 or quicker must be inspected every three years by NHRA and have serialized sticker affixed to roll cage before participation. See General Regulations 4:10, 4:11, 10:6.
Ground Clearance
Minimum 3 inches from front of car to 12 inches behind centerline of front axle, 2 inches for remainder of car (except for exhaust more than 12 inches behind centerline of front axle).
Parachute
Mandatory on any car running 150 mph or faster. See General Regulations 4:8.
Wheelbase
Must retain original wheelbase for body used, plus or minus 1 inch. Maximum wheelbase variation from left to right is 1 inch.
Tires
All applications limited to a maximum width of 9.0 inches and maximum height of 25.0 inches; DOT or racing slicks permitted. Rear skinnies permitted. Retreads, space-saver spares, or any other non-DOT-approved tire prohibited.
Wheels
Must be automotive-type wheels suitable for street or racing use. Minimum wheel size 13 inches unless originally equipped with smaller wheels and vehicle is equipped with original engine. Wheel studs must be threaded into hex portion of lug nut a distance at
least equal to the diameter of the stud. Spindle mounts prohibited. See General Regulations 5:2.
Interior
Complete interior, including dashboard, door panels, headliner, etc. mandatory. Rear seat may be removed, but all other upholstery and panels must remain in place. Two matching, upholstered front seats mandatory. Aftermarket seats permitted, but must be fully upholstered. All factory controls must be retained and operative; i.e., lights, signals, horn, windows, and wipers.
Body
Body must be on NHRA Accepted Bodies list. Pickup and SUV bodies prohibited.
Complete, OEM body structure mandatory, including floorpan, firewall, strut towers, wheel houses, etc. Chopped roofs prohibited. Mild customizing body kits permitted, but must retain full-bodied appearance, with minimum two functional doors. Doors must open and close from inside and outside. Windshield and all windows must retain OEM safety glass.
Lightweight body panels limited to hood and hatch or deck lid. Air inlet may not extend past the front bumper. Aftermarket body kits permitted, but full street-legal appearance must be maintained. One-piece aftermarket front end prohibited.
NHRA-approved front ends : JCR-EG3 (92-95 Civic); JCR-EKS (99-00 Civic); JCR-EF3 (88-91 CRX) and JCR-DC3 (98-00 Integra).
Competition Numbers
See General Regulations 7:2.
Firewall
OEM firewall mandatory. See General Regulations 6:1, 7:4.
Floor
OEM floorpan, front to rear, mandatory.
Street Equipment
Windshield wipers and OEM side mirrors mandatory. Complete headlight and taillight assemblies (all) mandatory; must be operative.
Windshield/Windows
Complete OEM windshield and windows mandatory. Windows must be operative per factory specifications. (Must open and close via electrical or OEM mechanical means.)
Batteries
Batteries must be securely mounted; may not be located in driver compartment unless sealed off per General Regulations. OEM 12- volt system mandatory. 16-volt b atteries/electrical system prohibited. See General Regulations 8:1.
Ignition
Two steps, rev limiters, etc. permitted. See General Regulations 8:1, 8:3, 8:4, 8:5.
Master Cutoff
Mandatory on any car running 9.99 or quicker, or 135 mph or faster, or on any car where battery is relocated to trunk area of vehicle. See General Regulations 8:4.
Computer
Prohibited. See General Regulations 9:1.
Data Recorder
Permitted. See General Regulations 9:2.
Fire Extinguisher System
Permitted; must be securely mounted. See General Regulations 9:3.
Two Vehicles
Prohibited.
Warm-Ups
See General Regulations 9:4, 9:12.
Credentials
All competitors must have competition number and membership number. Valid NHRA competition license mandatory for driver of any vehicle running 9.99 or quicker or 135 mph or faster. All drivers running 10.00 seconds or slower must have a valid state- or
government-issued driver's license beyond a learner's-permit level or valid NHRA competition license. See General Regulations 10:4.
Driver Restraint System
Three-inch-wide driver restraint system labeled as meeting SFI Spec 16.1 mandatory in any car required to have a roll bar or roll cage. System includes crotch strap and must be updated at twoyear intervals from date of manufacture. All other cars, OEM restraint system mandatory. See General Regulations 10:5, 10:11.
Helmet
Helmet meeting Snell K98, 2000, 2005 or SFI Spec 31.1A, 31.2A, 31.1/2005, 41.1A, 41.2A, or 41.1/2005 mandatory. Effective Jan. 1, 2008, full-face helmet mandatory on all cars 9.99 or quicker. See General Regulations 10:7.
Neck Collar
Mandatory on driver of any car running 9.99 seconds or quicker or 135 mph or faster. See General Regulations 10:8.
Protective Clothing
See General Regulations 10:10.
Power Street
Designation
Remove the following from the first paragraph second sentence:
Slicks allowed on naturally aspirated entries.
Engine
Remove the following from the first paragraph first sentence:
Naturally aspirated entries limited to 2.5 liters.
Tires
Replace the first paragraph with the following:
AWD and RWD 4-cyl forced induction applications, maximum tire size 245/60, NHRA/DOT approved radial tires only. FWD 4- and 6-cylinder applications, maximum tires size 235/60, NHRA/DOT approved tires permitted, racing slicks prohibited. Rear “skinnies” prohibited on all forced induction applications. Retreads, space-savers spares, or any non DOT-approved tire prohibited.
Power Street FWD NHRA/DOT-approved Tire List
Part # Nominal Size
MT
3752 10.5” by 26.1”
Hoosier
17410 9.3” by 26.1”
17400 9.5” by 26.1”
17430 9.3” by 26.1”
M and H
MHD-01 10.5” by 26”
MSS-008 9.8” by 25.4”
Replace the title of the approved tire list to:
NHRA/DOT-approved Radial Tires for AWD/RWD Applications
Remove the following from the title
(maximum rollout on drive tires 84 inches)
Turbo Street
Designations
Remove the following from this section:
Valid DOT registration and license plates mandatory.
Turbocharger
Replace the second paragraph with the following:
K-Series and Ecotec turbo applications limited to a maximum 67.8mm (2.669 inches) where the maximum compressor wheel diameter may not exceed 67.88 mm (2.672 inches) measured at the point where the leading edge of the compressor wheel meets
the housing; the compressor housing inducer diameter may not exceed 69.13mm (2.722 inches) measured at the point where the leading edge of the compressor wheel meets the housing. Compressor wheel inducer contours of wheel may not be stepped, notched, or clipped; e.g., the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing is prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic material wheels prohibited.
Tires
Please add the following “Accepted Tire List for AWD/RWD Four-Cylinder Applications” to this section:
Mickey Thompson
Type Part Number
DOT 3792
Slick 3052
Hoosier Tire
Type Part Number
DOT 17430
Slick 18120
Toyo Tires
Type Part Number
Slick 370210
Slick 370230
Body
Add the following to the end of the third paragraph:
NHRA-approved front ends : JCR-EG3 (92-95 Civic); JCR-EKS (99-00 Civic); JCR-EF3 (88-91 CRX) and JCR-DC3 (98-00 Integra).
Unlimited Street
Designations
Remove the following from this section:
Valid DOT registration and license plates mandatory.
Minimum Weights
Add the following to this section:
RWD 6-cylinder (1 or 2 power adders)
3.51 to 4.0 liter (214.19 to 2.44.09 cid) 3,350 pounds
Add the following to this section
Nitrous Oxide (364 ci) 3,125 pounds
(365 ci to 400 ci, add 5 pounds per cubic inch)
Exhaust
Replace this section with the following:
All cars competing in Unlimited Street may be required to run with functioning muffler(s) depending on track regulations. See General Regulations 1:3.
Supercharger
Add the following to the Unlimited Street Approved Supercharger list:
Kenne Bell Blowers 1.5L/1.7L/2.1L/2.2L/2.4L/2.6L/2.8L
Big Bore Kits Flowzilla
Blowzilla
Magnacharger Blowers MP45/MP62/MP90/MP112 4th and 5th Gen.
Whipple Blowers W140AX/W200AX/W200R/W305AX/W305R
Ford Motorsports Blowers 2.2L/3.4L/4.6L
Turbocharger
Replace the first paragraph in this section with the following
Eight-cylinder, single turbo applications limited to a maximum 80 mm (3.150 inches) where the maximum compressor wheel diameter may not exceed 80.5 mm (3.169 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 81.75 mm (3.219 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Replace “Four-cylinder, single turbo” in the second paragraph with “Four-cylinder and Six-cylinder (3.51 to 4.0 liter), single turbo”
Add the following paragraph to this section:
Eight-cylinder, twin turbo applications limited to a maximum 66 mm (2.598 inches) where the maximum compressor wheel diameter may not exceed 66.5 mm (2.618 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 67.75 mm (2.667 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph to this section:
Six-cylinder (3.51 to 4.0 liter), twin turbo applications limited to a maximum 68 mm (2.677 inches) where the maximum compressor wheel diameter may not exceed 68.5 mm (2.697 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 69.75 mm (2.746 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Transmission
Add the following new paragraph after the first paragraph
Approved transmission adapters: MAZ-10150; MAZ-10151; MAZ-10155 and MAZ-10156
Chassis
Add the following after the first sentence in the first paragraph:
Mini-tubes permitted on drag radial combinations only.
Battery
Replace this section with the following:
Batteries must be securely mounted; may not be located in driver compartment unless sealed off per General Regulations. See General Regulations 8:1.
Modified
Engine
Add the following to the end of this section:
8-cylinder applications limited to 449 ci maximum displacement.
Turbocharger
Replace “Two-rotor and four-cylinder, single turbo” in the first sentence of the fifth paragraph with “Two-rotor, three-rotor and four-cylinder, single turbo”
Replace the seventh paragraph in this section with the following:
Eight-cylinder, single turbo applications limited to a maximum 96 mm (3.779 inches) where the maximum compressor wheel diameter may not exceed 96.5 mm (3.799 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 97.75 mm (3.848 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Replace the eighth paragraph in this section with the following:
Eight-cylinder, twin turbo applications limited to a maximum 78 mm (3.071 inches) where the maximum compressor wheel diameter may not exceed 78.5 mm (3.091 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 78.75 mm (3.100 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph to this section:
Two- and three- rotor, twin turbo applications limited to a maximum 61 mm (2.401 inches) where the maximum compressor wheel diameter may not exceed 61.5 mm (2.421 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 62.75 mm (2.470 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Pro FWD
Minimum Weights
Add the following weight break
3RZ-FE (1 power adder only) 2,100 pounds
Turbocharger
Add the following paragraph below the Four-cylinder, single-turbo section:
3RZ-FE single turbo, applications limited to a maximum 95 mm (3.740 inches) where the maximum compressor wheel diameter may not exceed 75.5 mm (3.759 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 96.75 mm (3.809 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Pro RWD
Turbocharger
Replace the third paragraph with the following:
JZ and FZ series engines, single turbo applications limited to a maximum 88 mm (3.465 inches) where the maximum compressor wheel diameter may not exceed 88.5 mm (3.484 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 89.75 mm (3.533 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Add the following paragraph after the JZ and FZ series engines, single turbo section
FZ and JZ series engines, twin turbo applications limited to a maximum 66 mm (2.984 inches) where the maximum compressor wheel diameter may not exceed 66.5 mm (2.618 inches) measured at the point where the leading edge of the compressor wheel meets the housing; the compressor housing inducer diameter may not exceed 67.75 mm (2.667 inches) measured at the point where the leading edge of the compressor wheel meets the housing Compressor wheel inducer contours of wheel may not be “stepped, notched, or clipped”; e.g. the contours must be continuous features from the inducer to the wheel exducer. All air entering the turbocharger must pass through the turbocharger inlet. Injection of any liquid, gas, or any other substance into the inlet or exhaust housing in prohibited. Turbocharger compressor wheel must be constructed of cast or billet aluminum. Exotic materials wheels prohibited.
Wheelie Bar
Replace the second sentence of the first paragraph with the following
Maximum length of 75 inches for 4- and 6- cylinder applications and 85 inches for 8- cylinder applications.
Body
Replace the first paragraph with the following:
Body must be on NHRA Accepted Bodies list. Pickup and SUV bodies prohibited.
www.HotCampinas.com
- Desde 1997
www.Hot402.com - Desde 2020
www.Hot402.com - Desde 2020
Por favor Entrar ou Registrar para participar da conversa.
Re: POR QUE 3¨ de ALTURA NA ARRANCADA ?
05/04/2008 às 17:49
É ta ai , eu nao sabia destas coisas la de fora , mas falou o chifrudo mestre , mesma coisa q eu disse e realmente eu estava na reuniao das decisoes do regulamento e so nao arrebentei esse corno do Caca porque ele é muito pequinininho , nao compensa , um abraço Caca .
Jamanta
Por favor Entrar ou Registrar para participar da conversa.
Re: POR QUE 3¨ de ALTURA NA ARRANCADA ?
05/04/2008 às 17:52cacadaud escreveu: Seguinte,
Eu acho incrível a quantidade de opniões que saem neste forum.
Eu só queira lembrar vcs, que na maioria eu nunca vi em nenhuma reunião de regulamento..... que todas as alterações feitas nos regulemtos de curitiba e velopark foram votadas em reuniões em em ctba. Essas reuniões foram avisadas nos sites mais conhecidos de arrancada e também através dos comunicados qeu os pilotos que correm regularmente recebem antes das provas. O próprio Jamanta estava nessas reuniões e como ele mesmo explicou existe um motivo mais que coerente pelas 3´ mínima de altura. Para quem não sabe, o equipamento de cronomeragem de CTBA é americano, e as foto-células para funcionarem corretamente, ou seja, ascender primeiro o pre-stage e depois o stage, elas deve estar instalads no mínimo a 2,5´polegadas do chao. O problema nao e da fotocelula, e sim dos carros baixos demais. Mais uma vez, existiam varios carros alinhando pelo bandejao edeixando na duvida tanto o tempo de reacao quanto os 60 pes. Essa regra E SIM DO REGULAMENTO DA NHRA e todos, TODOS os carros lla tm que ter 3 de altura!!!!!!!!!!!!!!!!! Isso foi avisado VARIAS vezes no ano passado!!Alem disso existe a itencao de fazer as eliminatoria. Isso so sera possivel quando todos os carros poderem alinhar corretamente, ou seja, pre-stage e depois stage, pois os amarelos comecam imediatamente apos o alinhamento. Assim como a altura, o bandejao tambem e obrigatorio la, para se ter uma ideia vc e proibido de entrar na pista se seu carro sou uma gota de oleo antes mesmo de fazer o burn-out, se voltar do burn-out pingando alguma coisa, ai entao........ nem pensar..... isso la e muito rigoroso!!!!!! E claro que la tambem querbra motor, mas todos os pilotos quando quebram, tiram o pe e imediatamente vao ara o canto da pista. Isso por que, se sujar tem uns 20 caras e uns 3 tratores para limpar a pista, aqui e melhor nao sujar, por depois que suja nao limpa nunca mais.
Fora isso, todas as alteracoes como a proporcao de peso (72x28 ou 70x30), santo antonio, alavanca de cambio, tambem foram votadas nessas reunioes, as quais tinham uns 50 pilotos.
Vamos parar de reclamar e vamos andar!!!!!!!!!!!!!!!!! Nao tem como negar, o bandejao enche o saco, mas deixou a pista muito mais limpa, isso que tem muito bandejao por ai que nao protege porcaria nenhuma, mas isso, queira ou nao e protecao para todos.....
O Troyano, vc ta doidao hein, ahahahahahahahahhahaha Seu sindicalista do cacet........ ahahahahahaha Abracos pra vc e pra todos aqui
Vou comecar a postar aqui........
desculpe, mas fui apertando as teclas aqui e sumiram os ascentos e cecidilhas....... manezao mesmo!!!!
Ótima informação essa de 3" p/ mim era 1" o mínimo! (y)
Continue compartilhando conhecimento conosco hein biba! ahhaeuheau
Abraço!
www.HotCampinas.com
- Desde 1997
www.Hot402.com - Desde 2020
www.Hot402.com - Desde 2020
Por favor Entrar ou Registrar para participar da conversa.
Re: POR QUE 3¨ de ALTURA NA ARRANCADA ?
05/04/2008 às 17:53
caca, voce tem o privilegio de observar mais de perto o que acontece la fora, mais nao vejo vc falando da preocupacao que os caras tem a respeito do equilibrio das categorias .Ex um cara monta um carro com motor muito mais forte e com entre eixo maior e tudo favorecendo a esse projeto. esse cara nao anda com os outros (ex drag noorwod ) esta em uma categoria de exibicao.
Aqui e foda so se fala em regulamento onde o cara ve vantagem
Aqui e foda so se fala em regulamento onde o cara ve vantagem
"Anão voador"
Por favor Entrar ou Registrar para participar da conversa.
Re: POR QUE 3¨ de ALTURA NA ARRANCADA ?
05/04/2008 às 18:53
Xandola... Pistola..... seu anão do inferno!!!! Seguinte, até onde eu sei, o Drag do Norwood foi construído já sabendo que não existiria uma categoria para ele andar. Não existe regulamento para aquele tipo de carro, informação que tive através do Gary Kubo, marido da Lisa Kubo, que hoje é chefe de equipe do Chris Rado, e que o Norwood do é quem começou a fazer o carro dele a uns 3 anos atrás.
Quanto ao equilíbrio das categorias lá fora, isso é também é levado muito a sério. Por exemplo, se vc ler o regulemento da NHRA Sport Compact, que parece mais com as nossas categorias aqui, lá no final tem uam relação dos carros (chassis) que poderão ser usados para correr nas categorias. Depois disso, em cada categoria, existem as restrições de tamanho de turbo para cada tipo de motor, e mais ainda, se em um ano, passa-se a ter um superioridade muito grande de uma marca, ou um tipo de motor, vão existir mais restrições para isso, porém na maioria das vezes, as restrições são o aumento de peso do carro. Isso já até é assim, por exemplo, se vc quer correr na Hot Rod (a nossa FLTD), e que vai usar só turbo, vc pode pesar X, se vc vai usar turbo e nitro, vc vai ter que adicionar 25 quilos, se quiser adicionar um cambio especial vai mais peso ainda, e por aí em diante.
Agora, no fundinho mesmo eu sei bem o que vc quer dizer viu seu lazarento!!!!!!!!
Abração
Cacá Daud
PS.: Não tem ninguém que tem tempo aí para traduzir todo o regulamento da NHRA Sport Compact, principalmente o "introduction" e o "general regulations"??? Isso iria matar um monte de dúvidas de um monte de gente... por que se faz isso, por que se usa aquilo......
Só posso dizer uma coisa, tanto o pessoal de CTBA quanto do velopark estão fazendo essas alterações tomando como base o que está escrito lá!!! Isso eu garanto!!
Quanto ao equilíbrio das categorias lá fora, isso é também é levado muito a sério. Por exemplo, se vc ler o regulemento da NHRA Sport Compact, que parece mais com as nossas categorias aqui, lá no final tem uam relação dos carros (chassis) que poderão ser usados para correr nas categorias. Depois disso, em cada categoria, existem as restrições de tamanho de turbo para cada tipo de motor, e mais ainda, se em um ano, passa-se a ter um superioridade muito grande de uma marca, ou um tipo de motor, vão existir mais restrições para isso, porém na maioria das vezes, as restrições são o aumento de peso do carro. Isso já até é assim, por exemplo, se vc quer correr na Hot Rod (a nossa FLTD), e que vai usar só turbo, vc pode pesar X, se vc vai usar turbo e nitro, vc vai ter que adicionar 25 quilos, se quiser adicionar um cambio especial vai mais peso ainda, e por aí em diante.
Agora, no fundinho mesmo eu sei bem o que vc quer dizer viu seu lazarento!!!!!!!!
Abração
Cacá Daud
PS.: Não tem ninguém que tem tempo aí para traduzir todo o regulamento da NHRA Sport Compact, principalmente o "introduction" e o "general regulations"??? Isso iria matar um monte de dúvidas de um monte de gente... por que se faz isso, por que se usa aquilo......
Só posso dizer uma coisa, tanto o pessoal de CTBA quanto do velopark estão fazendo essas alterações tomando como base o que está escrito lá!!! Isso eu garanto!!
Por favor Entrar ou Registrar para participar da conversa.